Here is the passport organizer tutorial. You could use your scraps for this project which i did!
{material/supplies}
25 pieces of 2.5"x2.5" fabric - outer piece
1 piece of 10.25"x10.25" fabric- inner piece
2 pieces of 8.5"x10.25" fabric- large pockets
1 piece of 4.5"x12" fabric- folded card pocket
1 piece of 2.5"x4"- pen holder
cut 2.5" wide fabric and piece together for the binding
buttom
elastic
thread
sewing machin
{fusible craft interfacing}
cut
2 pieces of 10.25"x10.25" - outer piece/inner piece
2 pieces of 10.25"x8.5" - large pocket
1 piece of 12"x 4.25"- folded card pocket
25 piece of 2.5"x2.5" layout the pieces and make your own arrangement
sew the pieces together
please remember use 1/4" seam allowance for this project
press the back seams well, so you don't leave any unpressed area
iron your top piece to a fusible batting
recommend: heavy weight fusible batting
you can purchase it in joann's or local craft store
press well with the iron
watch for the corners
the corners tend to get miss out
recommend: no steam
after press the top piece and batting together
machine quilting is highly recommend
i used 1/4" straight stitches for my quilting
but please be creative you can use any stitches you like
after finishing quilting put this piece aside
2 pieces of 10.25" for the inner large pockets
2 pieces of 10.25" fusible interfacing.
you need to look at the shinning side where you will iron your fabric on
i got my in joann's and it is called craft fusible.
however, any fusible interfacing is durable.
there's no need to buy this type if you only have light weight fusible at home
recommend: craft fusible
press the two pieces on the interfacing
i like my interfacing slight larger than the fabric
i like to trim it down after press
there i can get the exact size i need
now, fold your two inner pocket pieces in half and press with iron
top stitch both pieces. it will make the piece look so professional
i like two top stitches for mine.
it just nice look and clean
remember 10 minutes ago you just pieced the outer piece with 25 pieces of 2.5"x2.5"?
this is the inner piece that's measure 10.25"x10.25".
again, you need a piece of 10.25"x10.25" craft fusible interfacing for it
and remember iron and press nice
so far you should have 4 pieces done and ready to set aside
this is a 2.5"x4"piece for your pen holder
first you fold the shorter side of the edge in
then fold the piece in half
press with iron
sew around the edges. please don't feel like making it perfect
it is a little trick sewing on small pieces
note: NO interfacing need for this piece
measure from the top where you want your pen to be
i had mine 2" away from the top
sew a small box on each side then a cross to secure the piece
on the inner piece 10.25"x10.25"
member card holding piece: 12"x4.5"
take one long side of the edge and fold 1/4"
iron a piece of 4.25"x12" fusible interfacing onto the piece
look close on the picture you only start the line that you have folded
so later when you are doing the multiple folding you will not create a bold folding seam
on the side of the interfacing
draw a measurement of 2" and 1.5"
here you'll create three 2" section and three section of 1.5"
leave the last part that is left blank
follow the lines that you drew from the last picture
and fold it as it go
press with iron
here you have create multiple folding
this would be the pre-pocket look
this side is the side where you previously folded 1/4"
as you can see the edge folds are pretty nice
remember the blank piece that you left?
now trim it down it about 1/4" and fold in
now, you would need one side of the large pocket you create
draw a line and that's the line where you'll attach your little pocket
how to measure the line?
lay your folded pocket down from the bottom of the large pocket piece
then you'll see the 1/4" piece location that would be the place you need to draw
you would sew the folded piece on the large piece
now stitch the folded pocket piece with the large pocket piece together
now bring all your pieces back and lay them down together
you should have the picture look
i am not sure if the passport is stander size for all countries
so measure your passport now
drew a light line on the large pocket piece (where you'll store you passport)
then stitch the pocket piece on the inner piece
sandwich all 4 pieces together. i used 1/8" seam for secure the pieces.
make sure the edges are clean and you are happy about it
create you binding
cute the fabric 2.5"wide
the length would depend on the final size of your piece
i used hair elastic for this organizer
attach the elastic onto the piece, piece it as shown on the picture
sew your binding on the sandwich piece
i prefer hand sewing my binding
don't forget attach a nice size button
the completed passport organizer inner look
0 comment:
Post a Comment